Zennio MAXinBOX FC 0-10V FAN-COIL Controller ZCL-FC010F

MAXinBOX FC 0-10V FAN : 

Controller for up to two 2-pipes or 4-pipes fan coil units with on/off valves and 0-10 V fan speed control signal. Mounted on DIN-rails (4.5 units). 4 multifunction outputs (16 A C-Load) that can be used for the control of the fan coil on/off valves or any other purpose. 4 analog-digital multifunction inputs that can be configured as binary inputs for sensors and potential-free push buttons, as temperature probe inputs or as motion sensor inputs. It also includes 2 thermostats and 10 logical functions. Manual control of outputs and status indication through LEDs. Accessories: temperature probe and motion sensor.

Zennio Fan-coil controller for a 2-Pipe or 4-Pipe fan coil with 0-10 DC valves-and up to 4 fan speeds-ZCL-FC010V

MAXinBOX FC 0-10V VALVE : 

Controller for one 2-pipes or 4-pipes fan coil unit with 0-10 V valves. Its 4 outputs (16 A C-load) can be used to control the fan speed or as individual outputs. it has 4 analog-digital multifunction inputs that can be configured as binary inputs for sensors and potential-free push buttons, as temperature probe inputs or as motion sensor inputs. It also includes 2 thermostats, 10 logical functions and allows manual control of the outputs with status indication through LEDs. DIN-rail mounting (4.5 units). Accessories: temperature probe and motion sensor.

Zennio Fan coil controller for up to 4 units of 2-pipes fan coil KNX ZCL-4XFC2P

Fan coil controller for up to 4 units of 2-pipes fan coil. It includes a module with 20 logical functions and allows manual control of the outputs with status indication through LEDs.

Zennio Fan coil controller for up to 2 units of 2-pipes fan coil KNX  ZCL-2XFC2P

Fan coil controller for up to 2 units of 2-pipes fan coil. It includes a module with 20 logical functions and allows manual control of the outputs with status indication through LEDs..

Zennio IRSC A/C Unit control device ZN1CL-IRSC

A/C unit control module. IRSC is a KNX infrared air conditioner controller able to manage more than 300 A/C unit models from different manufacturers. IR transmitter included.

Zennio MINiBOX 0-10V X1 Multifunction actuator with 1 0-10 V input/output analog channel ZIO1X010

Zennio MINiBOX 0-10V X2 Multifunction actuator with 2 0-10 V input/output analog channels ZIO2X010

Schneider-KNX-Valve Drive Controller-MTN6730-0002

 It is used to operate thermal servo-motors designed to control
control of hydraulic floor heating or cooling ceilings.
The actuator has 6 electronic outputs. Up to
connect up to 4 230 Vac thermal actuators or 2 24 Vac thermal
24 Vac thermal actuators to each output. Actuators
normally closed or normally open actuators can be
connected.
In addition, the actuator has 6 integrated temperature regulators
which operate independently of each other.
The correction variables of the controller outputs can be
connected internally to the actuator outputs, so that temperature
so that temperature control and servomotor actuation can be performed
can be carried out by a single device on the bus.
The integrated temperature controllers can send the
correction variable telegram on the bus and thus control other
control other heating or fan coil actuators.
The outputs are either switched (1 bit) or PWM (1
byte).
Each output is protected against overload and short-circuit.
All outputs can be controlled manually using
front panel pushbutton.
Panel mounting on rails.
The bus is connected via a bus terminal.