Airzone-Aidoo LG KNX Controller-AZAI6KNXLGE

Device to manage and integrate LG units in KNX TP-1 control systems. Externally powered by the indoor unit.

Features:

• Control of the parameters of the unit.
• KNX Control.
• KNX standard data.
• 3 digital inputs.
• Easily configurable from ETS.
• Communication errors detection.

Airzone-Aidoo KNX Daikin Residential KNX Controller-AZAI6KNXDA0

Device to manage and integrate Daikin Residential units in KNX TP-1 control systems. Externally powered by the indoor unit.

Features:

• Control of the parameters of the unit.
• KNX Control.
• KNX standard data.
• 3 digital inputs.
• Easily configurable from ETS.
• Communication errors detection.

Airzone-Aidoo KNX Daikin Sky Air KNX Controller-AZAI6KNXDA1

Device to manage and integrate Daikin Sky Air KNX Controller units in KNX TP-1 control systems. Externally powered by the indoor unit.

Features:

• Control of the parameters of the unit.
• KNX Control.
• KNX standard data.
• 3 digital inputs.
• Easily configurable from ETS.
• Communication errors detection.

ISE - Set SMART CONNECT KNX Vaillant S-0001-006

The SMART CONNECT KNX Vaillant is simply connected to the eBUS of your KNX installation. Use the ETS to make configurations, carry out set up and Bob's your uncle.

Intelligent heating control via KNX: Together with the system controllers sensoCOMFORT or multiMATIC, the SMART
CONNECT KNX Vaillant offers integration between the Vaillant system and KNX.
Features:
• Control of operation mode and temperature setpoint values for up to three heating zones
• Control of operation mode and temperature setpoint value for hot water supply
• Control of ventilation system operation mode
• System information like service mode, error messages, date and time, outside temperature and system status
• Heating circuit status values: Pump status, flow setpoint temperature, flow temperature, minimum flow setpoint
temperature for cooling mode, heating curve for each heating circuit
• Hot water status values: Circulation pump status, charging pump/3-way valve status, hot water temperature
• Display of temperature and error status for up to eight heat generators
• Yield values of solar systems and heatpumps
• Consumption values for hot water supply and heating (electricity and gas)
• Handover protocol from installer to system integrator
• Simple integration into KNX (can be completely configured via ETS)
• Easy-to-understand structure in the ETS5 thanks to channels
• Extensions via firmware updates

Zennio KLIC-MITTv3  Mitsubishi Air conditionner controller ZCLMITTV3

KNX-Mitsubishi Electric Gateway (IT connector)

Zennio gateway to control Mitsubishi Electric air conditioning units through IT terminal connector from KNX system in a bidirectional way. It includes 2 analog-digital inputs for temperature probes, motion sensor or dry contact binary inputs (switches, sensors or push buttons) and 10 logical functions.

Zennio KLIC-DI v2 Daikin KNX air conditioner controller (Industrial Range) ZCLDIV2

Zennio gateway to control Daikin commercial and industrial air-conditioning units from KNX system in a bidirectional way. It includes 2 analog-digital inputs for temperature probes, motion sensor or dry contact binary inputs (switches, sensors or push buttons) and 10 logical functions. 2 DIN rail units. Accessories: temperature probe and motion sensor.

KNX LOGIC INTERFACE FOR DAIKIN AIR CONDITIONER CONTROL ( LOW TEMPERATURE ALTHERMA RANGE )

• Small size: 90 x 90 x 35mm (2 DIN units)
• Does not require any power supply other than that of the Bus.
• Mounting on DIN rail (EN 50022), pressure mounted.
• KLIC DA offers half-duplex communication with hidrokit LT units.
• Integrated KNX BUS coupling unit.
• Complies with CE directives

You will find the list of compatible models for this product in the documents.

Zennio KLIC-DAv2 KNX-Daikin Altherma gateway ZCLDAV2

• Zennio gateway to control Daikin Altherma/Altherma 3 units from KNX system in a bidirectional way (see KLIC-DA’s Compatibility table). It includes 2 analog-digital inputs for temperature probes, motion sensor or dry contact binary inputs (switches, sensors or push buttons) and 10 logical functions. 2 DIN rail units. Accessories: temperature probe and motion sensor.