Schneider Power supply KNX -320 mA - MTN6513-1203

SpaceLogic KNX Power Supply 320 mA The SpaceLogic KNX power supply generates the bus voltage for the KNX line The power supply has two outputs – one KNX output with integrated choke and one DC 30 V output for additional devices The power supply has a floating signalling contact for operation and diagnostic message

Zennio 320mA KNX KUPSupply ZPSU320

KNX Universal System Power Supply with additional 29 V DC output. Maximum current 320 mA. 110-240 V ~ 50/60 Hz input voltage. Installation in DIN-rail (4.5 units).

Interra 320mA KNX power supply  ITR900-132 :

• Mounting Location: Installation only on a 35 mm DIN rail of a distribution board.
• Device needs at least 4 standard modules width at installation.
• Power supply has an additional 30 VDC short circuit and overload protected voltage output that can be used to power an additional bus line (in combination with a separate choke).
• The voltage output is overload, short circuit and over temperature protected.
• Output without choke can be used as a constant 30 VDC supply and output with choke can be used as a KNX Bus supply.

Interra 160mA KNX power supply  ITR900-116 :

• Mounting Location: Installation only on a 35 mm DIN rail of a distribution board.
• Device needs at least 4 standard modules width at installation.
• Power supply has an additional 30 VDC short circuit and overload protected voltage output that can be used to power an additional bus line (in combination with a separate choke).
• The voltage output is overload, short circuit and over temperature protected.
• Output without choke can be used as a constant 30 VDC supply and output with choke can be used as a KNX Bus supply.

Zennio 160mA KNX power KUPSupply-ZPSU160

Power supply KNX 160mA with 29VDC auxiliary power supply

• KNX system power source with additional 29VDC output.
• Supply voltage 230V~ 50/60Hz.
• Maximum consumption of KNX BUS line 160mA.
• Maximum additional 29VDC output consumption of 250mA -
• KNX coil included.
• Mounting on DIN rail (EN 50022), pressure mounted.
• Protection against short circuit and overvoltage.
• Reset button and overload status LED.
• Complies with CE directives.

Count 10mA per KNX participant to choose a KNX power supply.

Safety instructions:

• The installation must be equipped with a device that ensures omnipolar disconnection. A 10A circuit breaker is recommended.
• Do not connect the main network voltage or other external voltages to the KNX data bus or to the additional output.
• Connecting an external voltage may endanger the electrical safety of the entire KNX system.
• Always check during installation that there is sufficient insulation between the conductors of the 230V main voltage and the conductors of the Bus and its extensions.
• Do not cover the ventilation grilles to prevent the temperature acceptable to the device from being exceeded.
• Caution! Once the device has been installed, it must not be accessible from the outside.
• The electrical equipment must only be installed by qualified electricians and in accordance with accident prevention regulations.
• To prevent electrical accidents, before working on the unit, disconnect the main power supply with the circuit breaker located upstream of the unit.
• Failure to follow the installation instructions may cause damage to the installation.

Zennio ALLinBOX 46 Multifunction device - ZPR46

Multifunction device comprising :

• A KNX 160mA power supply
• A KNX-IP Interface
• 4 16A outputs
• 6 analog/digital inputs

Zennio ALLinBOX 88 Multifunction device - ZPR88

Multifunction device comprising :

• A KNX 320mA power supply
• a KNX-IP Interface
• 8 16A outputs
• 8 analog/digital inputs

Zennio ALLinBOX 1612 v2 Multifunction device - ZPR1612V2

The starting point for most projects incorporating control and monitoring functionalities. Multifunction device that integrates a 640 mA KNX power supply, KNX-IP Interface, 4 independent thermostats, logical module, 12 analog/digital inputs and 16 relay outputs (16A C-Load) in only 12 DIN rail units. Offers multiple configuration options as individual outputs, shutter channels or fan coil controller (2/4 pipes).