Input module
-
Theben - TA 2 S KNX - 4969222
Theben - TA 2 S KNX - 4969222
-
Function description
-
- Binary input/binary output sensor interfaces
- 2-way key interface
- 4-pole cable connection
- Free allocation of functions: Switch/key, dimming, blinds, valuator, sequences, controlling LED
- Can be installed in flush-mounted sockets with conventional sensors/switches
- Flexible LED controlling, thanks to increased output current of 3 mA commercially available LEDs and low curent LEDs can be controlled
- Inputs can be reconfigured to outputs with parameterizable flashing and pulsing function
- Colour coding of wiring pairs
-
54.60 € -
-
Zennio Bin 2X Universal interface with 2 binary inputs/LED outputs ZIO-BIN2X
BIN 2X is a module with 2 configurable channels as binary inputs or LED outputs. Binary inputs can be configured as sensors, switches or potential-free push buttons. Binary outputs can be used for low current LED control. Installation in standard mounting box.
56.00 € -
Interra 2 channels Universal interface ITR102
Interra ITR102 :
Description :
ITR102 device is used to interface the contacts to KNX bus substructure such as push buttons, switches etc. to make them communicating devices.
Configuration and features :
- The complete configuration of the device is performed via ETS3 or higher.
- Depending on ETS configuration and settings the product feature will be different.
- Avaialble functions are:
- Switching
- Dimming
- Toggle
- Blind Control
- 2 Channel
- Value Selected
- Most of functions only need one input and therefore each input might be assigned a different function. However there are also some functions which use two inputs such as “Dimming with 2 buttons” and “Shutter/Blinds with 2 buttons”.
Mounting, commissionning and safety notes :
- The device may only be installed and put into operation by a qualified electrician or authorized personnel.
- The device is inserted in a flush-mounted combined joint box.
- The installation location should not be in the outdoor area.
- The voltage potentials on the lines connecting the contacts are not electrically isolated from the bus voltage.
- Permitted cable length can be up to 5 meters and unused wires should be insulated.
- Avoid contact with liquids and corrosive gases.
- Do not get wrong connection for KNX Black and Red wires.
- Please do not forget to recheck all connections after installation
44.50 € -
Schneider-Push-button interface, 2-gang plus -MTN670802
Schneider-Push-button interface, 2-gang plus -MTN670802
Push-button interface, 2-gang plus. Generates an internal signal voltage for connecting 2 conventional push-buttons or floating contacts, and for connecting 2 low-current LEDs. The cores are 30 cm long and can be extended to max. 7.5 m. For installation in a conventional 60 mm switch box. KNX software functions: Switching, dimming or controlling blinds via 1 or 2 inputs, position values for blind control (8-bit), pulse edges with 1-, 2-, 4-, or 8-bit telegrams. Differentiation between short and long activation, initialisation telegram, cyclical transmission, pulse edges with 2-byte telegrams, 8-bit linear regulator, scenes. Counter, disable function, break contact/make contact, debounce time. Outputs for connecting control lamps (low-current LEDs) for the status display. For each input/output object type: Contact voltage: < 3 V (SELV). Contact current: < 0.5 mA. Output current: max. 2 mA. Max. cable length: 30 cm unshielded, can be extended up to max. 7.5 m with twisted unshielded cable. Dimensions: approx. 40x30.5x12.5 mm (LxWxH). Colour: polar white.
57.60 € -
Theben - TA 4 S KNX - 4969224
Theben - TA 4 S KNX - 4969224
-
Function description
- Binary input/binary output sensor interfaces
- 4-way key interface
- 6-pole cable connection
- Free allocation of functions: Switch/key, dimming, blinds, valuator, sequences, measuring temperature, controlling LED
- 2 NTC inputs for detection of the actual temperature from -5 °C to +100 °C
- Can be installed in flush-mounted sockets with conventional sensors/switches
- Flexible LED controlling, thanks to increased output current of 3 mA commercially available LEDs and low curent LEDs can be controlled
- Inputs can be reconfigured to outputs with parameterizable flashing and pulsing function
- Colour coding of wiring pairs
73.80 € -
-
Zennio Bin 4X Universal interface with 4 binary inputs/LED outputs ZIO-BIN4X
BIN 4X is a module with 4 configurable channels as binary inputs or LED outputs. Binary inputs can be configured as sensors, switches or potential-free push buttons. Binary outputs can be used for low current LED control. Installation in standard mounting box.
77.00 € -
Interra 4 channels Universal interface ITR104
Interra ITR104 :
Description :
ITR104 device is used to interface the contacts to KNX bus substructure such as push buttons, switches etc. to make them communicating devices.
Configuration and features :
- The complete configuration of the device is performed via ETS3 or higher.
- Depending on ETS configuration and settings the product feature will be different.
- Avaialble functions are:
- Switching
- Dimming
- Toggle
- Blind Control
- 2 Channel
- Value Selected
- Most of functions only need one input and therefore each input might be assigned a different function. However there are also some functions which use two inputs such as “Dimming with 2 buttons” and “Shutter/Blinds with 2 buttons”.
Mounting, commissionning and safety notes :
- The device may only be installed and put into operation by a qualified electrician or authorized personnel.
- The device is inserted in a flush-mounted combined joint box.
- The installation location should not be in the outdoor area.
- The voltage potentials on the lines connecting the contacts are not electrically isolated from the bus voltage.
- Permitted cable length can be up to 5 meters and unused wires should be insulated.
- Avoid contact with liquids and corrosive gases.
- Do not get wrong connection for KNX Black and Red wires.
- Please do not forget to recheck all connections after installation
53.50 € -
Schneider-Push-button interface, 4-gang plus -MTN670804
Schneider-Push-button interface, 4-gang plus -MTN670804
Push-button interface, 4-gang plus. Generates an internal signal voltage for connecting 4 conventional push-buttons or floating contacts, and for connecting 4 low-current LEDs. The cores are 30 cm long and can be extended to max. 7.5 m. For installation in a conventional 60 mm switch box. KNX software functions: Switching, dimming or controlling blinds via 1 or 2 inputs, position values for blind control (8-bit), pulse edges with 1-, 2-, 4-, or 8-bit telegrams. Differentiation between short and long activation, initialisation telegram, cyclical transmission, pulse edges with 2-byte telegrams, 8-bit linear regulator, scenes. Counter, disable function, break contact/make contact, debounce time. Outputs for connecting control lamps (low-current LEDs) for the status display. For each input/output object type: Contact voltage: < 3 V (SELV). Contact current: < 0.5 mA. Output current: max. 2 mA. Max. cable length: 30 cm unshielded, can be extended up to max. 7.5 m with twisted unshielded cable. Dimensions: approx. 40x30.5x12.5 mm (LxWxH). Colour: polar white.
88.80 €