KNX universal LED dimmer actuator, 2 outputs

 2 x 300W outputs for incandescent lamps 230 V or 4 x 7 to 50 W outputs for 230 V LED lamps 
ETS product family: Lighting
Type: Dimmer

Intended use

Switching and variation:

• incandescent lamps
• HV halogen lamps
• Tronic transformers with halogen lamps
• variable inductive transformers with halogen or LED lamps
• HT LED lamps
• compact fluorescent lamps
• Mounting on DIN rail in a sub-distributor according to EN 60715

Product features

• Automatic or manual selection of the variation principle adapted to the load
• Secure against no-load operation, short circuits and overheating
• Short circuit message
• Manually controllable outputs
• Return of the switching state and the change value
• Parameterizable variation and activation
• Timer functions: switch-on delay, switch-off delay, staircase light switch and warning function Light scene operation
• Locking of individual outputs manually or by bus
• LED status display of the outputs
• Operating hours counter
• A power failure longer than approx. 5 seconds will deactivate the dimming actuator. Depending on the parameter setting, the connected load is measured again after the mains voltage is restored.

Zennio DIMinBOX DX1 KNX 1 channel universal dimmer actuator ZDI-DBDX1

Main characteristics:

• 1 channel of 350W at 230VAC
• 1 channel for R L C type loads or variable LED bulbs and low consumption.
• Automatic detection of the R L C load type.
• Choice of dimming curves for LEDs and low consumption.
• Manual control of the dimming possible.
• Designed to be placed in any electrical box with DIN rail.
• Integrated KNX BUS coupling unit.
• Data backup in case of power loss.
• Complies with EC directives

Safety instructions :

• The equipment must only be installed by qualified electricians and in accordance with the accident prevention regulations. Do not connect the main voltage (110-230VAC) or other external voltages to the KNX Data Bus. Connecting an external voltage may endanger the electrical safety of the entire KNX system.
• Once installed, the device must not be accessible from the outside.
• In case of load change, disconnect the main voltage (110-230VAC).
• Always check during installation that there is sufficient insulation between the conductors of the 110-230VAC main voltage and the conductors of the KNX Bus and its extensions.
• Do not expose the device to rain or moisture, nor block the ventilation openings.
• Failure to follow the installation instructions may cause fire and other damage.

JUNG 1 output KNX dimmer actuator 500W 3901REGHE

1 output 500 W for incandescent lamps 230 V or 1 output 7 to 100 W for LED lamps 230 V
ETS product family: Lighting
Type: Variable speed drive/dimmer

Intended use

Switching and variation:

• incandescent lamps
• HV halogen lamps
• Tronic transformers with halogen lamps
• variable inductive transformers with halogen or LED lamps
• HT LED lamps
• compact fluorescent lamps
• Mounting on DIN rail in a sub-distributor according to EN 60715
• Speed control for regulating the speed of single-phase motors (e.g. induction motors, shaded ring motors or universal motors)

Product features

• Automatic or manual selection of the variation principle adapted to the load
• Secure against no-load operation, short circuits and overheating
• Short circuit message
• Manually controllable outputs
• Return of the switching state and the change value
• Parameterizable variation and activation
• Timer functions: switch-on delay, switch-off delay, staircase light switch and warning function Light scene operation
• Locking of individual outputs manually or by bus
• LED status display of the outputs
• Operating hours counter
• A power failure longer than approx. 5 seconds will deactivate the dimming actuator. Depending on the parameter setting, the connected load is measured again after the mains voltage is restored.

Zennio inBOX DIM dimmer for flush mounting ZDI-IBD

Universal dimmer (RLC, LED, CFL*) for flush mounting with one channel for up to 250 W at 230 VAC (200 W at 110-125 VAC). Auto load type detection (RLC). Configurable dimming curves for LED and CFL. It allows manual control of its outputs through the push buttons on the cover. It includes 10 independent logical functions. In addition, it incorporates 2 analog-digital inputs that may be configured as binary inputs for sensors and potentialfree push buttons, as temperature probe inputs or as motion sensor inputs. Error detection: short circuit, voltage surge, overheating, anomalous frequency and power failure. Accessories: Temperature probes and motion sensor. *Only dimmable loads.

JUNG Amplifier LED ULZ1755REG

rail mounting device, 2 rail units

Intended use

• Power extension of the listed dimmers (ref.-no.: UD 1755 REG, 1730 DD, 1731 DD, 1710 DE, 1711 DE, 1712 DE, FM UD 20250 UP, FM UD 5500 REG, FM UD 420250 REG, 3901 REGHE, 3902 REGHE, 39004 1S R)
• Mounting on DIN rail according to EN 60715 in distribution box

 
Product characteristics

• Connection of several amplifiers to a single dimmer
• The total power of the connected loads is divided between the dimmer and amplifiers
• Power is supplied to the connected loads via a common power cable
• Operation using upstream dimmer
• Electronic over-temperature protection
• Optional accessory: compensation module LED, ref.-no.: KM LED 230 U